HVAC replacement in Lake Nona, Florida built for Florida heat
New systems, honest pricing, and installs done in a day
When your old unit quits in the middle of a Lake Nona summer, you need HVAC replacement in Lake Nona, Florida from a team that knows this climate. We size, supply, and install Carrier, Trane, and Daikin systems for homeowners in Laureate Park, Storey Park, and Medical City. Most jobs finish in one day, and you get a system matched to your ductwork, not a guess off a truck.
What HVAC replacement in Lake Nona, Florida involves
HVAC replacement in Lake Nona, Florida is the removal and full installation of your home's heating and cooling equipment, including the condenser, air handler, coil, line set, and thermostat. It is not a repair. We recover the old refrigerant with a recovery machine, cut and flare new copper tubing, run a fresh PVC condensate line, and pressure-test the whole circuit before charging. Then we pull a deep vacuum with a vacuum pump and weigh in R-410A or R-32 refrigerant by scale, exactly to the manufacturer's spec.
Most Lake Nona homes we replace systems in were built between 2005 and 2022, and the original builder-grade units are hitting the end of their service life. Salt air near Moss Park, attic temps that push past 140 degrees in July, and year-round runtime wear out capacitors, contactors, and blower motors faster here than almost anywhere in Florida. If you are searching for heating and cooling replacement Lake Nona FL options because your system is short cycling or your power bill jumped, we can usually tell you in one visit whether replacement beats another repair.
Why Lake Nona homeowners replace instead of repair
A new system is not just cooler air. It is lower bills, fewer emergency calls, and equipment sized for the way Lake Nona homes actually run.
Lower monthly cooling bills
A modern 16-SEER2 system uses roughly 30 to 40 percent less electricity than a 10-SEER unit from 2008. In a 2,400-square-foot Lake Nona home, that often means $70 to $120 less per month from June through September. We also set up your Ecobee or Nest thermostat so it stops overcooling empty rooms.
Fewer 2 a.m. breakdowns
New compressors, capacitors, and blower motors do not fail the way 15-year-old parts do. Replacing a system with a failing compressor or a cracked heat exchanger removes the two most common causes of emergency HVAC replacement Lake Nona Florida calls. You stop keeping a repair number on the fridge.
Correct sizing, not guesswork
We run a full ACCA Manual J load calculation on every replacement. Oversized units short cycle, leave humidity high, and die early. Undersized units run nonstop. Getting the tonnage right the first time is the single biggest factor in how long your new system lasts in Central Florida.
Cleaner air and better humidity control
A matched coil and air handler with a MERV 11 filter pulls more dust, pollen, and mold spores out of the air than a mismatched setup. We also seal duct connections with duct sealant and aluminum duct tape, so cool air reaches your bedrooms instead of leaking into the attic.
How our HVAC replacement process works
Five steps, one day for most homes, and no surprises on the invoice. Here is exactly what happens from your first call to the final walkthrough.
In-home assessment
We measure your home, check window count and insulation, inspect the existing ductwork, and photograph the current equipment. You get a written Manual J load calculation and two or three equipment options at different price points. This visit takes about 60 to 90 minutes.
Equipment selection
You pick the system that fits your budget and goals, whether that is a straightforward Goodman or Rheem single-stage or a Mitsubishi Electric variable-speed heat pump. We confirm line set size, thermostat compatibility, and whether your electrical panel needs a dedicated circuit for the new condenser.
Installation day
Our crew arrives with the new equipment, a recovery machine, manifold gauge set, and vacuum pump. We recover the old refrigerant, remove the condenser and air handler, build new copper tubing and a PVC condensate line, and set the new equipment. Most replacements take six to nine hours.
Testing and commissioning
We pull a deep vacuum to 500 microns, hold it, then charge refrigerant by weight using a refrigerant scale. A combustion analyzer confirms furnace operation if you have gas heat. We check static pressure, temperature split, and amp draw on the compressor and blower before we call it done.
Walkthrough and registration
We show you the new thermostat settings, walk you through filter changes, and register your manufacturer warranty on the spot. You get the model and serial numbers in writing. If anything looks off in the first 30 days, we come back at no charge.
HVAC replacement expertise you can verify
Voltiva Forge has been installing and replacing HVAC systems in Lake Nona since 2022. Every technician on our replacement crews holds EPA Section 608 certification for refrigerant handling, and our leads carry NATE certification in air conditioning and heat pump service. We hold a Florida HVAC contractor license and follow ACCA Manual J and Manual D standards on every job. That means load calculations, duct sizing, and refrigerant charging are done to a written standard, not by feel. We work with Carrier, Trane, Lennox, Rheem, Goodman, York, Mitsubishi Electric, Daikin, American Standard, and Bryant equipment, so we can match a system to your home instead of pushing one brand.
- EPA Section 608 certified for refrigerant recovery, charging, and R-410A handling
- NATE-certified technicians on every replacement crew
- ACCA Manual J load calculations included with every quote
- Florida HVAC contractor license and full liability coverage
- AHRI-matched coil and condenser combinations for verified efficiency ratings
Why Lake Nona picks us for HVAC replacement
We are a local crew, not a call center. When you book HVAC replacement in Lake Nona, Florida with us, the people who quote the job are the people who install it.
One-day installs, most homes
Roughly 85 percent of our Lake Nona replacements finish in a single day. We start at 8 a.m. and you are running cool air by late afternoon. Two-story homes with zoned systems sometimes need a second day, and we tell you that upfront.
Upfront pricing, no surprise line items
Your quote covers equipment, labor, refrigerant, line set, permit, and haul-away of the old unit. If we find something during install that changes the scope, we stop and call you before doing the work. No invoice surprises.
Same-day and 24/7 options
If your system dies in August, we keep replacement slots open for emergencies. Call before noon and we can often have a new system running the same day. Our 24/7 HVAC replacement Lake Nona line stays open for no-cool calls.
Local to Lake Nona, not Orlando-wide
We work Lake Nona Central, Laureate Park, Lake Nona Estates, Northlake Park, and the Narcoossee Road Corridor every week. We know which neighborhoods have attic units, which have garage-mounted air handlers, and how HOA approval works here.
What is included in HVAC replacement
Every replacement we quote in Lake Nona includes the equipment, labor, refrigerant, line set, thermostat, permit, and haul-away of the old system. If your job needs duct modifications, a new electrical circuit, or a crane for a rooftop unit, we list those as separate line items so you see exactly what you are paying for.
What's Included
New condenser and air handler
Matched condenser and air handler or coil, sized to your home with an ACCA Manual J load calculation. We confirm AHRI-matched combinations so your efficiency rating is real, not a marketing number on the box.
New line set and condensate drain
Fresh copper tubing, flared and pressure-tested, plus a new PVC condensate line with proper slope and a float switch. Old line sets are a common source of refrigerant leaks after a replacement, so we replace them by default.
Refrigerant charge by weight
We pull a deep vacuum to 500 microns, hold it, then charge R-410A or R-32 refrigerant by scale to the manufacturer's exact spec. No guessing by gauge pressure, no overcharging, no short-lived compressor.
Thermostat and controls
A new Ecobee or Nest smart thermostat, wired and configured, including a C-wire run if your home does not have one. We set schedules, connect the app, and show you how to adjust it before we leave.
Permit and old equipment removal
We pull the Florida HVAC permit, schedule the inspection, and haul away the old condenser, air handler, and any debris. You do not need to be home for the inspection if you prefer not to be.
Commissioning and warranty registration
Static pressure, temperature split, and amp draw are all tested and recorded. We register your manufacturer warranty the same day and hand you the model and serial numbers in writing.
Problems HVAC replacement near Lake Nona Central solves
Most replacements we do in Lake Nona start with one of these five problems. Each one gets worse and more expensive the longer you wait, especially once summer hits.
System runs nonstop but never cools the house
A failing compressor or a refrigerant leak means the system is working harder for less cooling. Power bills climb $80 to $150 a month while indoor temps creep up, and the compressor eventually burns out completely.
We test refrigerant charge, compressor amp draw, and temperature split to confirm the diagnosis. If the compressor is gone or the leak is in the evaporator coil, replacement is usually cheaper than repair plus a recharge you will repeat next season.
Power bills jumped 40 percent year over year
Older 10-SEER systems lose efficiency as capacitors weaken and coils foul. A unit that ran at rated efficiency in 2010 might be running at 60 percent today, and you pay the difference every month.
We compare your current system's rated SEER to a modern 16-SEER2 or variable-speed option and show you the projected monthly savings. Most Lake Nona homeowners see the new system pay for part of itself within five to seven years.
Frequent repairs, three or more in two years
Once a system starts failing repeatedly, each repair is a bandage. Capacitors, contactors, blower motors, and igniters fail in sequence as the whole unit ages out, and you are paying $400 to $900 per visit.
We add up what you have spent on repairs and compare it to replacement cost. If you are past 60 percent of replacement value in repairs, we recommend a new system and give you a written breakdown so the math is clear.
Uneven cooling between rooms or floors
Hot upstairs bedrooms and a cold downstairs usually mean undersized ductwork or a single-zone system trying to serve two very different loads. It gets worse as the system ages and airflow drops.
We run a Manual D duct analysis and check static pressure. Sometimes a duct fix solves it. When the equipment is also past its life, we install a zoned system or a variable-speed unit that ramps to match demand.
Refrigerant leak that keeps coming back
R-410A recharges run $300 to $700 per visit, and if the leak is in the evaporator coil inside the air handler, the repair can cost more than half of a new system. Meanwhile, the leak keeps damaging the compressor.
We use an electronic leak detector and pressure test to pinpoint the leak. If it is in a serviceable location, we repair it. If it is in the coil or buried in a wall, we walk you through replacement with a new line set and coil.
When Lake Nona homeowners replace their HVAC
A 2006 home in Northlake Park with the original builder-grade 3-ton unit that just failed its third repair in 18 months.
We run a Manual J load calc, confirm the ductwork is serviceable, and install a 16-SEER2 Carrier or Rheem system with a new line set and Ecobee thermostat. One-day install, permit pulled, old unit hauled away.
New system running by 5 p.m. the same day, projected $85 to $110 monthly savings, and a 10-year parts warranty registered the same afternoon.
A two-story home in Laureate Park where upstairs bedrooms stay 6 to 8 degrees warmer than downstairs all summer.
We measure static pressure, find the return is undersized, and install a zoned variable-speed Mitsubishi Electric or Daikin system with a new upstairs return. The zoning lets each floor call for cooling independently.
Upstairs and downstairs within 2 degrees of each other, and the variable-speed compressor runs at low speed most of the day instead of cycling on and off.
A Lake Nona Estates homeowner with a heat pump that short cycles every 10 minutes and a power bill that jumped $140 in one month.
We diagnose a failing compressor and a refrigerant leak at the coil. Replacement with a new heat pump and matched air handler is cheaper than repair plus recharge plus a second repair next season.
System runs in long, efficient cycles, humidity drops from 58 percent to 48 percent indoors, and the next month's power bill is $120 lower.
A Storey Park family whose system died on a Friday night in July with a newborn in the house.
We dispatch a technician the same night for a temporary fix, then schedule a same-day replacement for Saturday morning. The crew arrives at 8 a.m. with a Rheem system sized for the home.
Cool air restored by 3 p.m. Saturday, and the family never spent a full night without AC. Emergency dispatch fee was credited toward the replacement.
Tools and methods we use on every install
Tools & Equipment
Manifold gauge set
Used to read high-side and low-side pressures during charging and to verify the system is operating within the manufacturer's pressure range at the target outdoor temperature.
Vacuum pump and micron gauge
Pulls the system down to 500 microns and holds it there before charging. Skipping this step leaves moisture in the line set, which destroys compressors and POE oil over time.
Recovery machine
Recovers the old R-410A refrigerant from your existing system so it can be reclaimed or disposed of legally, per EPA Section 608 rules. We never vent refrigerant to atmosphere.
Refrigerant scale
Charges refrigerant by weight, not by gauge pressure. This is the only way to hit the manufacturer's exact charge on a new system, and it is what separates a proper install from a guess.
Clamp meter and multimeter
Tests compressor amp draw, blower motor current, and control voltage. We record these numbers at commissioning so we have a baseline for future service calls.
Combustion analyzer
On gas furnace replacements, verifies combustion air, flue temperature, and CO levels. Required for safe startup and to confirm the heat exchanger is operating correctly.
Tube bender and flaring tool
Builds clean, kink-free copper line sets with properly flared connections. Poor flares are one of the top causes of refrigerant leaks on new installs.
Methods
ACCA Manual J load calculation
We measure square footage, window area, insulation values, and orientation to calculate the exact heating and cooling load for your home. This determines the correct tonnage. Skipping it is why so many replacement systems in Florida are oversized and short cycle.
ACCA Manual D duct design
We check supply and return sizing, static pressure, and duct leakage. If your existing ducts cannot move the CFM your new system needs, we modify them during install. A great system on bad ducts still underperforms.
AHRI-matched system pairing
We only install condenser and coil combinations that are AHRI-certified together. This locks in the rated SEER2 and HSPF2 numbers and keeps your manufacturer warranty valid. Mismatched equipment voids both.
EPA Section 608 refrigerant handling
Every technician who touches refrigerant on our crew holds EPA Section 608 certification. Recovery, recycling, and charging all follow federal rules, and we document the refrigerant we recover from your old system.
Commissioning with recorded data
We record static pressure, temperature split, refrigerant charge, and amp draw at startup. You get a copy. If anything drifts in the first year, we have a baseline to compare against instead of guessing.
How HVAC replacement runs in Lake Nona
Lake Nona sits in a pocket of Central Florida that runs hot and humid nine months out of the year, and cooling systems here work harder than almost anywhere in the country. Summer attic temperatures regularly hit 140 to 150 degrees, which cooks capacitors and shortens compressor life. Salt air near Moss Park and the southern lakes corrodes condenser coils faster than inland homes. Most of the housing stock was built between 2005 and 2022, so the original builder-grade equipment is now hitting 15 to 20 years old and failing in clusters. We size every replacement with a Manual J load calc that accounts for our humidity, and we set airflow to keep indoor relative humidity between 45 and 55 percent. If you are comparing HVAC replacement service near Lake Nona options, ask whether the quote includes a load calculation and a duct static pressure test. Ours always do.
Service Areas
Most homes here have attic-mounted air handlers with tight access. We bring compact equipment and plan for a longer install window on 90-degree days.
Newer construction with tighter envelopes means smaller tonnage is often correct. We see oversized systems installed by builders that short cycle and leave humidity high.
Larger square footage and multi-zone systems are common. We frequently install variable-speed heat pumps with two or three zones to handle the load split.
Original 2005-2007 equipment is failing across the neighborhood. We keep common tonnage in stock so same-day replacement is realistic.
Townhomes and condos with shared walls need careful line set routing and HOA coordination. We handle the paperwork and schedule around building rules.
Local Considerations
Attic temperatures above 140 degrees in summer
Shortens capacitor and contactor life and makes install day physically harder. We schedule attic work for early morning and use portable cooling when needed.
Year-round cooling demand with only 6 to 8 weeks of heating
Heat pumps make more sense than gas furnaces for most Lake Nona homes. We size the cooling side first and confirm the heat strip or heat pump handles our mild winters.
High humidity and frequent afternoon thunderstorms
Correct sizing and airflow matter more than raw tonnage. Oversized systems cool the air fast but leave humidity high, which feels clammy and grows mold.
Salt air near Moss Park and southern lakes
Condenser coils corrode faster. We recommend coated coils and rinse the outdoor unit every few months for homes within a mile of the water.
2006 builder unit replaced in Northlake Park
A 3-ton 10-SEER Goodman from 2006 that had been repaired three times in 18 months. Power bills ran $340 to $380 in summer, and the upstairs never got below 78 degrees. The compressor was pulling 22 amps, well above spec.
New 3-ton 16-SEER2 Rheem system with a matched coil and Ecobee thermostat. Install finished in one day. First full summer bill came in at $245, and upstairs bedrooms now hold 74 degrees. Compressor amp draw at commissioning was 14.2 amps.
Maintenance & Follow-up
Change the MERV 11 filter every 60 days, book a pre-summer AC tune-up in April, and rinse the condenser coil twice a year. That schedule keeps the system at rated efficiency and protects the 10-year parts warranty.
A single-zone 4-ton system in a 2,800-square-foot two-story home. Upstairs ran 7 degrees warmer than downstairs all summer, and the system cycled every 8 to 10 minutes. Static pressure measured 0.92 inches of water column, well above the 0.5 target.
New variable-speed Mitsubishi Electric heat pump with a two-zone damper system and a new upstairs return. Static pressure dropped to 0.48 inches. Upstairs and downstairs now track within 2 degrees, and the compressor runs at low speed most of the day.
Maintenance & Follow-up
Zone dampers need an annual check, and the variable-speed board should be inspected at each tune-up. We recommend a pre-summer tune-up and a winter furnace tune-up to keep both modes running clean.
A 2010 Trane heat pump failed on a Friday night in July with a newborn in the house. Indoor temp hit 84 degrees by morning. The compressor was locked up and the coil had a confirmed refrigerant leak. Repair quote came in at $2,400 with no guarantee.
Same-day replacement Saturday with a new 3-ton Rheem heat pump and matched air handler. Crew arrived at 8 a.m., cool air restored by 3 p.m. Indoor humidity dropped from 58 percent to 47 percent within 24 hours. Emergency dispatch fee was credited to the invoice.
Maintenance & Follow-up
Book a pre-summer AC tune-up each April, change filters monthly during heavy-use months, and keep the condensate drain clear. The new system carries a 10-year parts warranty and a 1-year workmanship warranty.
How much does HVAC replacement cost in Lake Nona Florida?
Most full replacements in Lake Nona run $6,200 to $14,500 in 2026, depending on system size, efficiency rating, and whether ductwork needs work. A straightforward 3-ton single-stage swap lands near the low end. Variable-speed heat pumps, zoning, or new duct runs push toward the top. We give you a written range after the in-home assessment, not over the phone.
Who replaces HVAC systems in Lake Nona?
Voltiva Forge does, along with a handful of other licensed Florida HVAC contractors. We have been replacing systems here since 2022 and work with Carrier, Trane, Lennox, Rheem, Goodman, York, Mitsubishi Electric, Daikin, American Standard, and Bryant equipment. Ask any contractor for their Florida HVAC license and EPA 608 certification before they start.
Can I get same-day heating and cooling replacement in Lake Nona?
Yes, when equipment is in stock and we have an open slot. Call before noon and we can often complete a same-day heating and cooling replacement in Lake Nona, FL for standard single-system homes. Two-story homes, zoned systems, or jobs needing a crane for rooftop units usually schedule within 24 to 48 hours.
How long does HVAC replacement take in Lake Nona?
A typical single-system replacement takes six to nine hours, start to finish. We arrive around 8 a.m. and you have cool air by mid to late afternoon. Homes with two systems, attic access issues, or duct modifications can stretch to a day and a half. We confirm the timeline when we schedule.
Licensed, certified, and reviewed
Certifications
Reviews
Voltiva Forge replaced our 2007 unit in Laureate Park. They ran a Manual J, gave us three options with real numbers, and finished the install in one day. Our summer power bill dropped about $90. The crew cleaned up the attic better than they found it.
Called on a Friday night when our system died in Storey Park. They had a technician out within two hours and replaced the whole system Saturday morning. Fair price, no upsell, and they credited the emergency fee toward the install.
We got four quotes for HVAC replacement in Lake Nona. Voltiva Forge was the only one that measured the house and checked our ductwork. They found the return was undersized and fixed it during install. House cools faster and the humidity is finally under control.
Straightforward pricing, on-time arrival, and no pressure to buy the most expensive system. They explained the difference between single-stage and variable-speed in plain language and let us pick. The new Ecobee thermostat setup alone saved us about $60 a month.
Related Services
furnace repair
If your furnace still has life left, repair beats replacement. We diagnose ignition failure, flame sensor faults, and blower motor issues across Lake Nona before recommending a full swap. Many homeowners pair a furnace repair with a new AC condenser to spread cost.
furnace repairair conditioning repair
Not every no-cool call means replacement. We check refrigerant charge, capacitors, contactors, and the evaporator coil first. If a $400 repair buys you three more years, we will tell you that instead of quoting a new system.
air conditioning repairfurnace replacement
When your furnace is past 15 years or has a cracked heat exchanger, replacement is the safe call. We install gas and electric furnaces sized to match your existing ductwork and pair them with your new AC or heat pump.
furnace replacementair duct cleaning
New equipment on dirty ducts loses efficiency fast. We clean supply and return runs, remove debris from the plenum, and seal leaks with duct sealant. It is the cheapest way to protect a new system in older Lake Nona homes.
air duct cleaningheating repair
Florida winters still drop into the 30s in Lake Nona, and a failed heat strip or ignition module leaves you cold. We repair gas and electric heating systems, usually same day, before the cold snap hits.
heating repairheat pump repair
Heat pumps handle both heating and cooling here, so a failure hits year-round. We diagnose reversing valve issues, defrost board faults, and refrigerant leaks on Mitsubishi Electric, Daikin, and Trane heat pumps.
heat pump repairemergency HVAC repair
When your system dies at 11 p.m. in July, we answer. Our emergency line covers no-cool and no-heat calls across Lake Nona, with priority dispatch for homes with infants, elderly residents, or medical equipment.
emergency HVAC repairAC repair
Frozen coils, clogged condensate drains, and failed capacitors are the three most common AC failures we see in Lake Nona. Most repairs finish in one visit and cost far less than replacement.
AC repairheating and cooling repair near me
If you are searching heating and cooling repair near me in Lake Nona, we cover both sides of your system. One technician handles the AC and the furnace or heat pump in a single visit, so you are not paying two trip charges.
heating and cooling repair near meventilation system maintenance
Bathroom and kitchen exhaust fans, fresh-air intakes, and ERV systems all affect indoor air quality. We clean, test, and balance ventilation components so your new HVAC system is not fighting stale, humid air.
ventilation system maintenanceHVAC maintenance
Twice-a-year maintenance keeps a new system under warranty and running at rated efficiency. We check refrigerant charge, clean coils, test capacitors, and replace filters. It is the cheapest insurance you can buy for a new install.
HVAC maintenanceAC installation
New construction and add-on AC installs are a big part of what we do in Lake Nona. We size, run line sets, build plenums, and commission the system to ACCA standards, whether it is a single-zone or multi-zone setup.
AC installationair conditioner replacement
Air conditioner replacement is the cooling half of a full HVAC replacement. If your furnace or heat pump is fine but the condenser is done, we swap just the cooling side and match the coil to your existing air handler.
air conditioner replacementsmart thermostat installation
We install and configure Ecobee and Nest thermostats with every replacement, including C-wire runs if your home does not have one. Proper setup alone can cut cooling costs 8 to 12 percent in Lake Nona homes.
smart thermostat installationsame-day HVAC service
Same-day service covers repairs and replacements when we have open slots. Call before noon and we will do everything we can to get a technician to your Lake Nona home the same day, including weekends.
same-day HVAC servicefurnace maintenance
Annual furnace maintenance catches igniter wear, flame sensor carbon buildup, and heat exchanger cracks before they become safety issues. We recommend it every fall, before the first cold front reaches Central Florida.
furnace maintenancepre-summer AC tune-up
Book a pre-summer tune-up in April or May. We clean the condenser coil, check refrigerant charge, test capacitors and contactors, and clear the condensate drain so your system is ready for the June heat.
pre-summer AC tune-upwinter furnace tune-up
Even in Florida, a furnace tune-up in November pays off. We test ignition, verify gas pressure, inspect the heat exchanger, and confirm the blower is moving the right CFM before the first cold night.
winter furnace tune-upHVAC repair near me
If you need HVAC repair near me in Lake Nona, we are local. Our trucks are in the neighborhood daily, which means faster arrival windows and technicians who already know the layout of your community.
HVAC repair near melocal HVAC repair
Local HVAC repair means no Orlando dispatch delays. We are based in the Lake Nona area and cover Lake Nona Central, Laureate Park, Storey Park, and Randal Park with the same crew that handles our replacements.
local HVAC repair24/7 HVAC repair
Our 24/7 line stays open for no-cool and no-heat emergencies. A live person answers, and we dispatch the nearest available technician. Nights, weekends, and holidays are all covered.
24/7 HVAC repairAC repair near me
AC repair near me searches usually mean the system just quit. We diagnose refrigerant leaks, frozen evaporator coils, clogged condensate drains, and electrical shorts, then give you a straight repair-or-replace answer.
AC repair near meheating and cooling near me
One call covers both heating and cooling near me needs in Lake Nona. We service gas furnaces, electric heat strips, and heat pumps, so you are not juggling two contractors when something fails.
heating and cooling near mecentral air repair
Central air repair covers the full system: condenser, evaporator coil, line set, air handler, and ductwork. We test static pressure and temperature split to find the real problem, not just the symptom.
central air repairAC tune-up
An AC tune-up is a 60 to 90 minute visit that cleans coils, checks refrigerant charge, tests electrical components, and clears the drain line. It is the cheapest way to avoid a mid-summer breakdown in Lake Nona.
AC tune-upGet HVAC replacement in Lake Nona, Florida scheduled today
We are licensed, EPA 608 certified, and local to Lake Nona. Call (844) 796-4282 and we will book your in-home assessment, usually within 24 hours. Same-day replacement slots are available for no-cool emergencies.